我们热爱生命科学!-生物行

Axon Patch Clamp Amplifiers for Ele

时间:2006-06-20 20:30来源:www.intracel.co.uk 作者:admin 点击: 1643次

 

MULTICLAMP 700B Current and Patch Clamp Amplifier
Computer-controlled microelectrode amplifier for resistive-feedback patch clamp, high speed current lamp, voltammetery, amperometry ion selective measurement and bilayer recording.

Supplied with two CV-7B headstages enabling the unit to perform as two patch clamps, two current clamps or a combination of patch and current amplifiers. Addition of optional HS-2 voltage follower headstages allows 3 rd and 4 th point voltage recording.

 

AXOPATCH 200B Patch Clamp Amplifier

Ultra low noise amplifier using capacitor-feed-back technology in single channel mode. Low noise performance is assisted by cooling of active elements.

Maximum external bandwidth 100kHz. features include ZAP (to rupture patches when going into whole-cell mode), dual speed current-clamp, scaled output gains, variable low pass filters and leak subtraction. Membrane capacitance and electrochemical measurement capacity are standard. The single CV203BU hybrid Headstage can be used in single-channel, whole-cell and current clamp modes.

 

AXOCLAMP 2B High-compliance Voltage and Current Clamp Amplifier

Suitable for a wide range of intracellular microelectrode recording including continuous /discontinuous current clamping, continuous /discontinuous single electrode voltage clamping, two electrode voltage clamping up to + 130v.

Supplied with two:

HS-2A unity gain headstages and two HL-U pipette holders.

 

GENECLAMP 500B Voltage Clamp, and Patch Clamp and Voltammetry Amplifier

This is a high compliance voltage clamp and current clamp amplifier. The two HS-2A headstages, supplied may be used for intracellular recording and voltage clamping. A 3 rd (optional) headstage CV-5 can be used for patch clamping .

 

DIGIDATA 1322A. High Speed Data Acquisition System

 Data acquisition system with analogue and digital outputs and inputs. The system is completely contained within a BNC interface box, and includes a PCI SCSI adapter, a SCSI cable, and AxoScope acquisition software. The Digidata 1322A digitises with a maximum aggregate speed of 500kHz. The system has 16-bit resolution on the analogue inputs and outputs, 16 analogue inputs, 2 analogue outputs, 16 digital outputs, 16 digital inputs, and additional trigger inputs and outputs. Peak-to-peak input noise is 12mV.

The Digidata 1322A replaces both the 1320A and the 1321A.

 

pCLAMP9 Electrophysiology Data Acquisition Software

 The pCLAMP9 software suite includes Clampex9 and Clampfit9 (Data Acquisition and Analysis) programs. These offer a host of new features compared with the earlier (pCLAMP8 etc.) versions. pCLAMP9 is supplied with the MiniDigi-1A digitizer run by AxoScope 9 (also provided). This connects to the computer (via a USB port) and provides 2 channels of ‘chart recorder’ data.

Basic computer requirements are as follows:

IBM-compatible PC 400MHz
128 MB RAM
1024 x 768 Video card
CD-ROM drive
1 parallel / USB port (or 2 USB Ports)
PC1 slot
Windows 98 or higher
Digitizer (supported digitizer are Digidata 1322A, 1320A, 1321A, 1200A, 1200B).

Intracel

Tel 01763 262680 Fax 01763 262676

(责任编辑:泉水)
顶一下
(0)
0%
踩一下
(0)
0%
------分隔线----------------------------
发表评论
请自觉遵守互联网相关的政策法规,严禁发布色情、暴力、反动的言论。
评价:
表情:
用户名: 验证码:点击我更换图片
特别推荐
推荐内容