Wednesday, November 19, 2003
Description Most RNase Protection protocols require an overnight hyb with numerous subsequent clean-up steps. This method requires a maximum hyb of four hours, and the clean-up steps are the barest minimum, yet still produce nice images. It is strongly recommended to titer RNase concentrations with probes prior to running experiments...some require more RNase than others. Procedure Part I: In Vitro Transcription In a sterile 1.5ml microfuge tube, combine the following: ("ul"= microliter; all reagents obtained from Promega) 4 ul 5x Transcription Buffer 2 ul 0.1M DTT 4 ul 2.5mM NTP's (A, C, G) 0.8 ul RNasin RNase Inhibitor (25U/ul) (Promega) 2.4 ul of 100uM cold UTP (Note: Use 1mM UTP for loading control probes e.g. B-actin) 1 ul of 1 ug/ul linearized DNA template 5 ul of 10 uCi/ul P32 UTP (800Ci/mmol) (Dupont NEN - #NEG507X), or 1 ul for loading control probes 1ul RNA polymerase SP6,T7 or T3 (concentration varies by vendor) Total Volume ~20ul. Incubate 1 hour @ 37C. Add 2ul of DNase I (Promega) to each transcription, incubate 20 minutes @ 37C. Part II: Probe Purification Purify probes using QIAGEN QIAquick Nucleotide Removal Kit or Boehringer Spin Columns (G50 Sephadex). Check 1ul in scintillation counter, P32 channel. A good probe will be ~ 5x105 to 1x106 cpm. Part III: Hybridization Turn heatblock on to 95C. For samples in water or ethanol, dry down appropriate amount of RNA, and include a tube with 1ul of tRNA or Glycogen (Sigma), this is the negative control. Each sample should have the following: 24ul Formamide 2ul 0.6M PIPES 2.4ul 5M NaCl 0.3ul 0.1M EDTA 2 x105 cpm main probe 5 x104 cpm loading control probe DEPC water Total Volume 30ul Mix samples well. Heat @ 95C for 10 minutes. Incubate 4 hours @ 55C. Part IV: RNase Digestion RNase Digestion Buffer: 300mM NaAc 10 mM TRIS 5 mM EDTA To each sample add 350ul Digestion buffer. Add 1ul of 4mg/ml RNase A and 0.4ul of 10u/ul RNase T1. Incubate @ 30C for 45 minutes to 1 hour. Part V: Proteinase K To each sample add 10ul of 20% SDS and 2.5ul of 10mg/ml Proteinase K. Incubate @37C for 15-20 minutes. Part VI: Clean-Up Extract once with 400ul of Phenol/Chloroform/Isoamyl Alcohol (25:24:1) Transfer the supernatant to a new tube. Add 1000ul of 100% ETOH and 1ul of 10mg/ml of Glycogen. Mix well. Incubate samples at -70C for 30 minutes or in a dry ice/ETOH bath for 10 minutes. Spin in microfuge for 15 minutes. Aspirate ETOH. Allow pellets to air dry. Resuspend in 8ul of Formamide based loading dye. Allow to sit at RT for 5-10 minutes, with frequent mixing. Part VII: Polyacrylamide Gel Analysis Heat samples for 5 minutes @ 100C. Load onto a 5% polyacrylamide/7M Urea denaturing gel with 2000cpm of a molecular weight marker (dCTP labelled pBR 322 MspI digest works nicely). Run gel @ 38-42 mA. Dry gel, expose to film O/N at -70C with an intensifying screen. Recipes Supplies Tips (责任编辑:泉水) |